Compra ahora y paga después! Financia tus compras en 3 cómodos plazos con Klarna.

Advice and installation support via WhatsApp. Write to us now!

Settings

CANBUS Configuration (for vehicles with CANBUS)

Make sure the CANBUS module is properly connected:

Canbus module connection

Quad :

Enter the Car Settings application, Factory section , CarType Configuration , password 000000 / 16176699 , select the canbus brand and car model

Octa :

Enter the Car Settings application, Factory section , CarType Configuration , password 000000 / 8888 , select the canbus brand and car model

 

Steering wheel control configuration (for vehicles WITHOUT CANBUS)

Quad :

Make sure that no CANBUS configuration has been previously applied by going to Car Settings , Factory section , CarType Configuration , password 000000 / 16176699 , check that no option is selected, then go to General , SWC and leave it on Learning

After this go into Car settings , Factory section , Learning physical keys and configuring the controls to your liking

Depending on the software, the last step may be to enter the SW Learning application to configure the controls to your liking.

Octa : 

Make sure that no CANBUS configuration has been previously applied by going to Car Settings , Factory section , CarType Configuration , password 000000 / 8888 , check that no option is selected, then go to General , SWC and leave it on Learning

After this go into Car settings , Factory section , Learning physical keys and configuring the controls to your liking

Depending on the software, the last step may be to enter the KeyStudy application to configure the controls to your liking.

 

Rear Camera Connection

VEHICLES WITH CANBUS


* THE ⓸ CABLE IS LOCATED IN THE MAIN WIRING HARNESS OF THE RADIO, IN SOME MODELS IT IS USUALLY LABELED AS "REVERSE" OR "BRAKE" . IF IT IS NOT LABELED, IT IS MARKED IN THE FOLLOWING PHOTO AS ⓷ .

 

VEHICLES WITHOUT CANBUS

* THE ⓸ CABLE IS LOCATED IN THE MAIN WIRING HARNESS OF THE RADIO, IN SOME MODELS IT IS USUALLY LABELED AS "REVERSE" OR "BRAKE" . IF IT IS NOT LABELED, IT IS MARKED IN THE FOLLOWING PHOTO AS ⓷ .

Rear Camera Settings

Quad : 

Go to Settings , Factory , Password 000000 , Reverse Detection.

Octa :

Go to Settings , Car Infotainment , About device , click on the gear at the top right , password 8888 or 8878 , Backar Setup , look for CamType and select the appropriate option for our camera

Differences V1C & V1 Pro C / V1 Plus

V1C and V1 Pro C

The V1C and V1 Pro C variants are our most economical options, they have a 4-core processor, a resolution of 1024*600, RDS, GPS connectivity, Wi-Fi Fi and Bluetooth, and wireless Android Auto & Apple CarPlay systems. These variants do not support reversing cameras with 1080P resolution.

V1 Plus

The V1 Plus variants have an 8-core processor, 1280*720 HD resolution, GPS connectivity, Wi-Fi, Bluetooth, 4G (inserting a SIM card) RDS, GPS connectivity, Wi- Fi, Bluetooth, wireless Android Auto & Apple CarPlay systems, additional RCA wiring with SIM card slot and DSP equalizer options.

CANBUS configuration (for vehicles with CANBUS)

CANBUS CONNECTION IMAGE

V1C and V1 Pro C

Enter the application Car Settings, section Factory or Factory, CarType Settings, password 000000 , select canbus brand and car model SEE IMAGE

V1 Plus

Enter Settings, Car infotainment, About device or About device, click on the upper right gear, password 8888 u 8878, CAN Type, click ALLand search for the car model. Once this is done, click on SAVE and restart the computer SEE IMAGE

Steering wheel control configuration (for vehicles WITHOUT CANBUS)

V1C and V1 Pro C

Make sure that no CANBUS configuration has been previously applied by entering the Car Settings application, Factory or Factory section, CarType Settings, password 000000, and check that nothing is selected.

After this, enter Car settings, General, SWC Type, leave it at Learning Type, enter Enter SWC setting interface and configure the controls to your liking SEE IMAGE

V1 Plus

Ensure that no CANBUS configuration has been previously applied by entering Settings, Car infotainment, About device or About device , click on the upper right gear, password 8888 or 8878, CAN Type, check that the CAN Type option is 0

After this, go to Settings, then Car Infotainment, SWC, configure the steering wheel controls by pressing the function we want on the screen and leaving the steering wheel button that we want to program pressed SEE IMAGE

Rear camera

V1C and V1 Pro C

Enter Settings, Factory, password 000000, Reverse detection.

V1 Plus

Enter Settings, Car Infotainment, About device or About Device, click on the top right gear, password 8888 u 8878, Backar Setup, we look for CamType and select the appropriate option for our camera
Back to the start